Pro Max Compatible Garage Door Opener Parts. Pro Max Compatible Garage Door Opener Parts » Pro Max Compatible » Programming Instructions » Genie Wireless Keypad Entry System. Associated model numbers: GPWK, GWK, or GWK- BLImportant Information. WARNING - Moving Door can cause serious injury or death. DO NOT install transmitter unless the door operator's safety reverse works as required by the door operator's manual. Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts. Keep people clear of opening while door is moving. DO NOT allow children to play with the transmitter or door operator. My new Genie wireless keypad will not work with my garage door opener! I just bought this new Genie wireless keypad and it will not program to my opener!If safety reverse does not work properly. Close door then disconnect operator using the manual release handle. DO NOT use transmitter or door operator. Refer to Door and Door Operators Owner's Manuals before attempting any repairs. Electrical Shock can cause serious injury or death. Power cord must be unplugged before attaching any wires. Genie INTELLICODE Keypad garage door opener wireless keypad This keypad will. 7.Press and hold the program button until the light on keypad changes from. Genie Gwkic Garage Door Opener Keypad Intellicode Opener. Genie GK-BX Garage Door Opener Pro. Mount the keypad out of the path of the moving garage door. 13 = 12 DIP switch Genie garage door. Be sure wire ends do not touch each other or other terminals. If you have questions or if you need a manual, contact the distributor or manufacturer of the operator. Your code block with dip switches can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. Mounts with only two screws, and powered by a standard 9volt battery (included). Power saver. Slide up keypad cover to automatically turn on unit. Genie Garage Door Opener Remote Controls, we have Genie Remotes, Keypads and all accessories. This Keypad has been Discontinued by Genie. Program Your Garage Door's Opener. If cover is left up, the unit will shut off approximately one minuet after the last button is pressed. Low- Power warning. When LED does not flash, battery needs to be replaced. The unit will continue to function for a limited period of time. NO Memory Loss when battery dies or is replaced. Unique Slide- Up Keypad Cover provides maximum security and helps protect Keypad from the elements. How to Program a Genie Garage Door Opener. Program a Genie Intellicode Garage Door. Two- Step Programmability for maximum security and user convenience. Any Key Operation. After correct code is entered and door is activated, depress any key within 3. Security Lockout. After three incorrect Personal Identification Numbers (PIN) are entered, the unit will shut off for one minute. Installation instructions. Step 1- 1 Mount Wireless Keypad on a flat vertical surface with enough room above to slide cover up. Pick location out of path of moving garage door and supporting hardware. Step 1- 2 Slide Keypad Cover up and pull off wireless Keypad. Slide off battery cover and remove battery. Step 1- 3 Mark two holes by tapping a small nail through screw holes on keypad. You need a Genie garage door opener and a Genie keypad. Other than that, you need a ladder to help with reaching the garage door opener. After the visit of relatives you can reset garage door opener Genie Intellicode keypad and your access code will. Genie Garage Door Opener Program For Non. Genie Garage Door Opener Wireless Keyless Entry Systems & Wired Keypads. Genie GWKP/ACSD1G Garage Door Opener Wireless Keypad. Genie Garage Door Opener 9 or 12. Replace Keypad Cover. Step 1- 4 Replace battery and slide battery cover back into place. Determining your door code. Step 2- 1 Locate Operator Code Switches on Door Operator. Step 2- 2 Mark down your Operator Switch Settings by circling U (Up) or D (down) for each switch setting. Step 2- 3 Convert each group of three switch settings to a group number. NOTE: On new operator installation you MUST set Operator Code on Door Operator and Remote Control Transmitters before you begin programming this Wireless Keypad. Refer to the Owner's Manual for setting these switches. If you have not done this on your existing Door Operator. DO SO NOW! If your Door Code is 7,7,7 or 7,7,7,7 DO NOT CONTINUE. Refer to your Owner's Manual for setting of Door Operator and Remote Controller Security Code Switches. DO NOT LEAVE AT FACTORY SETTINGS. Selecting your personal identification (PIN)Your PIN number can be created from any group of numbers up to 8 digits of your choice. Goes out. Step 5. Slide Keypad Cover down Step 6. Test Keypad . Press * button. Goes out Slide Keypad Cover Down Test Keypad . Step 2 To change door code only. Action. Red light Any time you wish to change the DOOR CODE, you MUST first change the Security Code Switch settings on the Door Operator and all Remote Control Transmitters, then go to 4 DETERMINING YOUR DOOR CODE. Slide Keypad Cover down If you have any problems, refer to the troubleshooting section. Programming the keypad. Step 1 - Slide Keypad Cover up until it latches. Enter PIN and press * button. Step 2 - Slide keypad cover down. Keypad cover not fully open. Pull Keypad Cover up until it catches open. Replace battery. Door does not open. Reenter PINRed light blinking 2. Door code does not match door opener. Open sliding Keypad Cover completely. Replace battery as soon as possible. Programmed memory is not lost while replacing battery. For security, occasionally press other buttons or change PIN so all buttons get worn and dirty. A blinking red light indicates a wrong PIN was entered. A wrong PIN entered 3 times causes Keypad to shut down temporarily as a security measure. While the door is moving, you can control it by pressing any numbered button on the Wireless Keypad. If door begins closing and you need to stop it, press any numbered button on the Keypad and the door will stop operating. THIS DEVICE SHOULD NOT BE OPENED. THERE ARE NO USER SERVICEABLE PARTS OR OPERATOR CODE SWITCHES INSIDE OF UNIT. We invite your inquiries regarding your garage door opener. For technical and compatibility issues, we must know the brand and model of your opener to help. Be sure to include your complete and accurate email address with your inquirygarage- door- opener- parts. Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2017
Categories |